Tankless Water Heater Installation and Repair

A tankless water heater heats water only when you open a tap, so it never runs out the way a tank does. PipeMend plumbers size, install, descale and repair gas and electric tankless units.

  • Gas and electric units
  • Sizing by flow and climate
  • Descaling and repair

Quick answer: Tankless water heater installation replaces a storage tank with a wall-mounted unit that heats water as it flows. The Department of Energy says tankless units can be 24 to 34 percent more efficient than a tank in homes using 41 gallons or less of hot water a day, and they can last more than 20 years. Correct sizing, gas line, venting and descaling make or break the results.

Tank vs. tankless: how they work

A tank water heater keeps stored water hot all day; a tankless unit heats water only while a tap is open Tank water heaterTankless water heater Holds a full tank of water Burner or elements keep it hot, even when no one uses it Runs out after heavy use, then needs time to recover Flow sensor starts the burner when a tap opens Hot water as long as you stay within its flow rate Cold in (blue) · hot out (copper) Vent on top for gas units · heat exchanger coil inside A tank water heater keeps stored water hot; a tankless unit heats water only while a tap is openTank water heaterHolds a full tank of waterKeeps it hot even when unusedCan run out after heavy useThen needs time to recoverUsual life: 10 to 15 years (DOE)Tankless water heaterFlow sensor starts heatingonly when a tap opensNever runs out if you staywithin its flow rateCan last 20+ years (DOE)
A tank stores and reheats water; a tankless unit heats it on demand through a heat exchanger.

What tankless water heater service includes

  • Sizing by peak flow in gallons per minute and the temperature rise your climate needs.
  • Gas line check and upsizing when the unit needs more gas than the old tank.
  • Venting: new stainless or PVC venting to the manufacturer's specs.
  • Electrical: a condensate pump or outlet for gas units; dedicated circuits for electric units.
  • Isolation valves so the unit can be flushed without draining the house.
  • Descaling with a pump and descaler, plus inlet filter cleaning.
  • Repair of error codes, ignition failures, flame sensors, flow sensors and fans.

Sizing a tankless water heater

Tankless sizing has two numbers. The first is flow: how many gallons per minute you need when the most fixtures run at once, such as two showers and a sink. The second is temperature rise: how much the unit must heat incoming water. The Department of Energy's Building America program says this depends on your area's winter cold water temperature and your hot water setting. Water in northern states can arrive much colder than in the South, so the same unit delivers fewer gallons per minute in Minnesota than in Florida. The DOE says high-efficiency tankless units can provide hot water at 2 to 5 gallons per minute.

The tankless installation process

  1. Assess. The plumber measures gas line size and length, checks the electrical panel and plans the vent route.
  2. Size and quote. You get a written estimate with the unit, gas, venting, electrical and permit work spelled out.
  3. Remove the tank. The old heater is drained, disconnected and hauled away.
  4. Mount the unit. The DOE notes that units should be installed level with rust- and corrosion-proof hardware.
  5. Connect. Water lines with isolation valves, the gas line, venting, the condensate drain and power are installed.
  6. Start up and test. Gas pressure, combustion, flow and outlet temperature are checked, and the setpoint is set.

Venting in cold climates

Gas tankless units vent hot exhaust and, in condensing models, produce acidic condensate that must be drained. The DOE says cold-climate units should be sealed-combustion, direct-vent or power-vented. It also says vents should sit above the expected snow line, with the intake far enough from the exhaust to prevent frost buildup. Getting this wrong causes shutdowns in winter.

Tankless water heater repair

ProblemCommon cause
No hot water, error codeIgnition failure, gas supply, flame sensor, blocked vent
Hot then cold ("cold water sandwich")Short gaps between uses; a recirculation setting can help
Water never gets hot enoughToo many fixtures at once, scale on the heat exchanger, undersized gas line
Unit will not start on low flowFixture flow below the unit's start-up rate; dirty inlet filter
Shuts off in cold weatherVent or intake frost, freeze protection fault

For tank heaters, see water heater repair.

Is tankless right for your home?

Tankless works well for small spaces, for long showers, and for homes that keep a heater for many years. The DOE says savings are largest in homes using 41 gallons or less a day, and smaller (8 to 14 percent) in homes using around 86 gallons a day. A tank may still make more sense when upfront cost matters most, or when the gas line or electrical service would need a costly upgrade. Compare both with tank water heater installation.

What affects the cost of a tankless water heater

  • Gas or electric, and the unit's size and brand.
  • Gas line upsizing and new venting.
  • Electrical work: a new circuit, or a panel upgrade for electric units.
  • Recirculation pumps or a water softener ahead of the unit.
  • Permit fees and removal of the old tank.

DIY or call a professional?

You can clean the inlet filter and follow the owner's manual for descaling if the unit has isolation valves. Installation, gas work, venting and electrical hookups need a licensed plumber and usually a permit. Many manufacturers also require professional installation for the warranty.

Keep it safe and efficient

  • Set the temperature around 120°F. The CPSC urges this setting to prevent scalds.
  • Descale on the schedule in your owner's manual, more often with hard water.
  • Keep vent terminals clear of snow, leaves and nests.

Tankless water heater questions

Do tankless water heaters really never run out?

They do not run out the way a tank does, but they have a flow limit. If more taps are open than the unit can heat at once, the water gets cooler. Sizing to your busiest moment avoids that.

How long do tankless water heaters last?

The U.S. Department of Energy says tankless units can last more than 20 years, compared with 10 to 15 years for most storage tanks. Regular descaling in hard water areas helps them reach that.

Why does my tankless water heater go cold in the middle of a shower?

Common causes are too many fixtures running at once, scale on the heat exchanger, a dirty inlet filter, a low-flow fixture below the unit's start-up flow, or a gas supply line that is too small.

Can I switch from a tank to a tankless water heater?

Usually, yes. Gas units often need a larger gas line and new venting. Electric units need a lot of electrical capacity, sometimes more than older panels can supply. The plumber checks both before quoting.

How often should a tankless water heater be descaled?

It depends on your water hardness and the manufacturer's instructions. In hard water areas, many manufacturers call for a vinegar or descaler flush about once a year. A water softener ahead of the unit reduces scale.

Related plumbing services

Water heater installation

Tank and heat pump water heaters sized, permitted and installed to code.

Water heater repair

No hot water, leaks, noises or a pilot that will not stay lit, on gas and electric tanks.

Water softener installation

Water softeners and filters sized to your water test and plumbed in with a bypass.

Sources

Last reviewed November 19, 2026 by PipeMend Editorial. General information, not legal, insurance or professional advice. Read our editorial policy.

Leak, clog or no hot water?

Call PipeMend 24/7 to get a licensed plumber started on the fix.

Call 1-800-555-0199
Call PipeMend 1-800-555-0199