Backflow Testing and Prevention
Your water utility or city may require a yearly backflow test, especially for irrigation, fire sprinklers and businesses. PipeMend arranges testing, repairs failed assemblies and installs new preventers.
- Annual test reports
- RPZ, DCVA and PVB
- Repair and installation
Quick answer: Backflow testing checks that the backflow preventer on your water line still stops dirty water from flowing back into the drinking water supply. A qualified tester attaches a gauge to the assembly's test cocks and checks each valve, then files a report with the water utility. Failed assemblies are repaired or replaced and retested.
How backflow happens
What backflow service includes
- Annual testing with a calibrated differential pressure gauge.
- Test reports filed with your water utility by its deadline.
- Repair of check valves, springs, seals and relief valves.
- Replacement of assemblies that can't be repaired.
- New installation for irrigation, fire lines, boilers and businesses.
- Freeze protection with insulated enclosures or seasonal draining.
- Cross-connection surveys to find unprotected connections.
Types of backflow preventers
| Assembly | Protects against | Common use |
|---|---|---|
| Reduced pressure zone (RPZ) | Backsiphonage and backpressure, high hazard | Businesses, medical, chemical lines, some irrigation |
| Double check valve assembly (DCVA) | Backsiphonage and backpressure, low hazard | Fire sprinkler lines, some irrigation |
| Pressure vacuum breaker (PVB) | Backsiphonage | Lawn sprinkler systems |
| Atmospheric vacuum breaker (AVB) | Backsiphonage | Hose bibbs, simple irrigation |
| Air gap | All backflow, by physical separation | Sinks, tanks, dishwasher drains |
The backflow testing process
- Schedule. You share the notice from your utility and the assembly's location.
- Short shutoff. Water to the protected line is shut off briefly for the test.
- Test. A gauge is attached to the test cocks, and each check valve and relief valve is checked against required readings.
- Report. Results are recorded and filed with the water utility, and you get a copy.
- Repair if it fails. Worn parts are replaced, and the assembly is retested.
Why backflow testing is required
The EPA's cross-connection control manual says water suppliers must protect the public system from backflow hazards. That includes the testing, installation and ongoing operation of backflow prevention assemblies matched to the degree of hazard. An EPA fact sheet describes a real case: an irrigation line was connected to a public system without an approved assembly, irrigation water flowed back, and customers were told not to use their water. Your annual test is part of preventing that.
Backflow risks at home
Backflow isn't only a business issue. A garden hose left in a bucket of fertilizer, a pool or a sprayer can siphon back into household pipes if water pressure drops, for example during a water main break. That is why many codes require vacuum breakers on outdoor hose bibbs, a pressure vacuum breaker or other assembly on lawn sprinkler systems, and an air gap on dishwasher drains. Homes with boilers, wells tied to city water, or rainwater systems may need more protection. A plumber can check your home's connections.
What affects the cost of backflow service
- Type and size of the assembly.
- Number of assemblies on the property.
- Repairs needed after a failed test.
- Access, enclosures and freeze protection.
- Permit and filing fees set by your utility.
DIY or call a professional?
Backflow testing must be done by a tester who meets your state and local requirements, using calibrated equipment, so it is not a DIY task. What you can do: know where your assembly is, protect it from freezing, and keep the utility's test notice so deadlines aren't missed.
Protect your backflow preventer
- Insulate or drain outdoor assemblies before freezing weather.
- Keep the assembly accessible, not buried in landscaping.
- Don't remove or bypass a preventer; it is often required by law.
- Test on schedule and keep copies of the reports.
Backflow testing questions
What is backflow?
Backflow is water flowing the wrong way, from a sprinkler system, boiler, pool or business process back into the drinking water supply. It happens when pressure in the public line drops (backsiphonage) or pressure on the private side rises (backpressure).
Why do I have to test my backflow preventer every year?
Backflow assemblies have springs, check valves and seals that wear out without any visible sign. Many water utilities and states require testing, often once a year, by a tester qualified under local rules, with results filed with the utility.
Who can test a backflow preventer?
Most areas require a tester who holds the credential your state or local rules call for. Many states require certification of backflow assembly testers. Your water utility can tell you its requirements and deadlines.
What happens if my backflow test fails?
The assembly is repaired, usually by replacing check valves, springs, seals or the relief valve, and then retested. If it can't be repaired, it is replaced. Utilities set a deadline to correct a failed test.
What types of backflow preventers are there?
Common ones are the reduced pressure zone assembly (RPZ) for high-hazard connections, the double check valve assembly (DCVA) for lower hazards, the pressure vacuum breaker (PVB) common on lawn sprinklers, and the air gap, the simplest method.
Related plumbing services
Commercial plumbing
Plumbing for restaurants, offices, stores and rental buildings, including grease traps.
Water line repair
Main water service line leaks, low pressure and line replacement to the street.
Leak detection
Hidden leaks in walls, ceilings and yards found with acoustic, thermal and pressure tests.
Sources
- EPA: Cross-connection control manual
- EPA: Protecting water quality through cross-connection control and backflow prevention
- EPA: Drinking water distribution system tools and resources
Last reviewed November 19, 2026 by PipeMend Editorial. General information, not legal, insurance or professional advice. Read our editorial policy.
Leak, clog or no hot water?
Call PipeMend 24/7 to get a licensed plumber started on the fix.
Call 1-800-555-0199